






Device Chip
Use to remediate strongest Wi-Fi, Bluetooth or EMF-emitting electronic sources such as:
Wi-Fi/Internet Routers (see Important Considerations section below).
Newer Smart TVs (especially after 2020 or any in the bedroom)
Wi-Fi printers, Smart Speakers (Alexa, Google Home), Wi-Fi Extenders, etc.
Gaming Stations & Gaming Controllers
Baby Monitors
Beds which “plug in” – such as adjustable beds, beds with a grounding mat, etc.
Everything Bluetooth or Wi-Fi (most importantly those found in the bedroom)
All Fans, AC Units, Air Purifiers & other Rotating Electric Motor devices – especially ones in or near your bedroom! *Please see below for more info. *
Cordless House Phones
Heating pads: I’m not a big fan of Electric heating pads. Don’t use them. However, an infrared heating pad, can be protected by our device chip. These are deeper penetrating into the body. https://www.costco.com/purerelief-pro-far-infrared-xl-heating-pad.product.4000204952.html
Dimensions: 0.25″ x 0.9″ x 0.9″
Important Considerations
** Home harmonizers will protect you if you are 12 feet or more away from routers. But if you are less than 12 feet away, especially while sleeping, put a device chip on there in addition to whole house harmonizer. With the Device chip on the router the zone distance where it causes DNA damage goes down to 1-2 inches.
** EMF Sources listed above often measure over 1,000 times higher than the Safe Levels (Safe Levels = one’s which do NOT produce “Biological Effects” according to BioInitiative.org & others)!
** Most don’t realize that household fans produce a disruptive Electromagnetic Field which is a different type of EMF that is harder for our products to remediate. So we suggest for best results not only using a Device Chip but also keeping fans, etc, at least 5 feet from the edge of your bed as well. Also we suggest avoiding the blade-less fans which are too hard to remediate altogether!
NOTE FOR YOU
This product will never be perfect looking but is near perfect performing. Here’s why: All resin-made products by EMF Solutions, including this one, are imperfect looking because of a safer, less toxic, plant-based resin that takes 3 long days to dry (as opposed to the chemical based resins which take minutes to dry). The dry resin isn’t perfect looking but we sacrifice looks for health and performance.
INSTALLATION INSTRUCTIONS
(See instruction videos as well as written instructions)
WRITTEN INSTRUCTIONS
Clip this to the electric cord as close as possible to the device or appliance that you are wanting to remediate. Ideally the square chip should press up against the electric cord. If the cord is too thick you can use electric tape to adhere the chip to the electric cord. If you’re remediating a Wi-Fi router, etc, be sure you clip the electric cord (not a CAT5 or other cord). Devices which need remediation (even after using the Room Harmonizer or Home Harmonizer for general overall remediation) include all stronger microwave producing devices such as Wi-Fi & bluetooth-like devices. See below for the list of EMF DEVICES which need a Device Chip.
EXCEPTIONS THAT NEED 2 or 3 DEVICE CHIPS:
FANS - All other fans other than Ceiling Fans need 2 chips AND to be 6 ft or more from the edge of your bed. The cord MUST BE on the same side of the cord. See product pictures for example. If you have a tower fan instead of the Device Chip you could take a Better ZZZs product and place it under the tower so that the electric cord runs right over the Better ZZZs.
WI-FI 7 ROUTERS - These need 3 Device Chips all in a row. Cord MUST be on the same side of all 3!
HOW TO FIX A CEILING FAN: These need only one Device Chip since they spin slower than other fans. Usually you can place the chip by itself on top of the flat metal edge of the fan. You can tape it there. If you can't do this then unscrew the cup cover and clip one Device Chip onto any one of the wires inside.
Use Device Chips to remediate strongest Wi-Fi, Bluetooth or other EMF-emitting devices, such as:
(In approximate order of importance:)
Wi-Fi Routers
Wi-Fi Extenders (tape chip to front)
Newer Smart TVs (especially ones after 2020 or located in a bedroom)
Wi-Fi printers
Smart Home Devices (such as Alexa or Google Home)
Gaming Stations & Gaming Controllers
Baby Monitors
Beds which “plug in” – such as adjustable beds, beds with a grounding mat, etc. Do NOT use Better ZZZs on these!
Everything Bluetooth or Wi-Fi - (most important devices are ones you touch, are close to, and spend much time using...and the least important are ones opposite of that which you use less often)
Fans, AC Units, Air Purifiers & other Rotating Electric Motor devices – most importantly the ones in or near your bedroom! Please see below for more info. ** NOTE: Fans, AC Units, etc, NOT in your bedroom are lower priority.
Cordless House Phones (main unit only…and phones you use frequently you can tape the chip to the back over the battery)
Other Wi-Fi/Bluetooth Devices, such as: iRobot main station & unit, Cordless Security Systems, Bluetooth Speakers, Bluetooth toys, more
IMPORTANT: Do you need to fix devices when you DO NOT USE the Bluetooth or Wi-Fi functions?
Answer - yes (usually). To explain, some devices shut down or turn off the EMF radiation once the Bluetooth or Wi-Fi functions are specifically "Disabled" from the menu. But many devices, such as newer Smart TVs, still emit EMFs even after you have disabled the Wi-Fi or Bluetooth functions. Some devices also automatically reset back to "Enabled" once the device turns back on. So it is safest to remediate all Bluetooth/Wi-Fi devices unless you are absolutely sure you can disable the EMFs altogether.
OTHER EXAMPLES OF HOW & WHERE TO INSTALL DEVICE CHIPS: